How To Tie In A New Roof To An Existing Roof

Converting a flat roof to a gable roof is a roofline change that requires a contractor with experience in roofing and carpentry. Now it is time to use a cut valley in order to tie the new shingles in with the old roofing system.


Image result for patio cover tie into existing roof

After the addition roof is framed and sheathed, snap a line on the existing roof shingles 2 in.

How to tie in a new roof to an existing roof. The new roof will also need to meet with building codes in your area. Patio cover tie into house. Up from the valley center, and cut through the shingles and underlayment.

Mark the proper height on the existing roof and snap a chalk line across the width of the area for the new shed roof. After framing and sheathing the new addition’s roof, snap a line over the existing roof shingles. For retrofitting an existing roof, we are planning on extending out a new rafter (to match existing roof pitch) out from an existing roof truss.

I am having trouble finding the best way to tie the two together in the valley, as far as the asphalt shingling goes. For example, materials like shingles can become brittle over time making this process more difficult. Measure with a tape measure and cut with a circular saw.

The lower the slope the further it should extend. You want to be about two inches above the very center of the valley itself. Strctpono (structural) (op) 10 sep 21 20:25.

See also  How To Recover From Wisdom Teeth Removal Fast

How to tie a additions roof to existing roof, roof to roof, двухскатная крыша присоединенная к односкатной below are 23 best pictures collection of how to attach a roof to an existing roof photo in high resolution. Reroofing an existing roof that abuts the new addition. First the 4×4 beams need to be cut to the size of the existing roof, so the porch roof and the edge of the existing roof will be even when the job is complete.

Now take the 4×4 beams and erect them to the perimeter outside the porch about four feet apart. Below are 14 best pictures collection of attaching a roof to an existing roof photo in high resolution. With either nails or using the mounting brackets attach the.

To tie into the side of an existing roof, put a new roof truss on the walls of the addition, brace it upright, then snap chalklines on the shingles to mark the center line of the new roof valleys, where old and new roofs will connect. I don't know if this is the best detail to accomplish this. This method may be one of the most ubiquitous ways of attaching a patio roof.

I'm building an addition to a ranch style home. You will need to evaluate if your existing walls can support the weight of a new roof. Tie new roof extension to existing truss.

The easiest way to tie in the new shingles with the old is with a cut valley (see four ways to shingle a valley). Depends on the slope of the new roof. Remove all shingles and roofing paper from that section.

See also  How To Get Rid Of Mean Mockingbirds

The ridge of the new roof falls well below the ridge of the house roof. Here are 7 different ways of attaching a patio roof to an existing house that you can apply. The new flashing should go under the old felt and over the new felt and new roll roofing.

Roofing nails to the existing structural sheathing. Leave the wood roof decking in place, but mark locations of all rafters or joists to which it is fastened. As it turned out, the existing roof structure is a truss system, but they were able to contact the original truss manufacturer to verify that cutting the tails off would not jeopardize the structural integrity of.

Fix the back channel to the fascia boards underneath the gutter directly. Tie a new gable or hip roof to an existing gable or hip roof with valley rafters, which perform the same function as ledgers. Strip the roofing from the old roof at the connection point to.

I cannot seem to get the tie in from the new roof to the existing roof correct. To tie the design together, peter chose to cut the rafter tails off the extend the exterior wall up to the underside of the new roof. The big idea is that layers of the lower roof should sit below corresponding layers of the upper roof.

The addition consists of adding a bathroom suite and an octagonal sitting area to the corner of the home. I'm relatively new to revit 2020. We will answer any further questions and can provide you with a free estimate.

See also  How To Remove Hair Tint From Carpet

Raising the pitch of the roof is a big job. Click the image for larger image size and more details. Click the image for larger image size and more details.

Any help would be appreciated, as well, i would be happy to compensate in return.


Carport Progress Rafters & Roof Design (And How The New


620 best images about bump out addition for house on


room addition with an existing Gable roof Roof trusses


open gable patio cover design Building a Gable end porch


Carport Progress Rafters & Roof Design (And How The New


tying into a exsisting roof at the same time. Next


roof framing Front Porch Addition Lauras Room


framing additions Google Search Porch roof, Roof


Roof Trusses Roof trusses, Roof, Timber


1000+ images about Roof on Pinterest


Building A Gable End Porch Cover. Tying Into Existing Roof


How it Works Collar and Rafter Ties (With images


Hipped roof exposed rafter ties Exposed rafters, Hip


Building A Gable End Porch Cover. Tying Into Existing Roof


Another lowpitched gable roof. How would this tiein to


Framing An Exterior Wall 5 How To Tie In Gable Roof


patio addition with multiple pitches Tying A Patio Roof


Image result for metal roof layers Metal roof, Rigid

Leave a Reply

Your email address will not be published.