Card are req.) 40361 (mach 2.0) el/gl series, control with sl550. To unlock the panel, press time, jets 1 and then cool.
The gfci pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How to reset balboa hot tub control panel. Hot springs green light blinking. The most common method is to switch the hot tub off for about 20 seconds and then turn it on again. If one of these keypads is used as an auxiliary panel, it locks when the main panel is locked.
I have a hot tub with balboa electronics, the heater will not come on and there is a failure code that says the sensors are out of balance. Each function will echo from the circuit board to the lcd in a corresponding manner. All other options work fine.
Manufactured under one or more of these patents. Furthermore, how do i reset my hot tub control panel? Also asked, is there a reset button on a hot tub pump?
A blinking red light on the control panel may indicate it needs to be reset. Switch the circuit breaker connected to your balboa hot tub to the off position. Press mode button to clear message.
How to reset a spa heater. Turn off the power to the spa. Topside control panel the control panel activates functions at the touch of a button.
This is a red button found on many spa packs. Remove cabinet panel, and covering for the control system. The spaside control panel, it's just a convenient way to turn things on and off, and view equipment status lights and water temperature.
Control your hot tub from your smartphone. If you remove the cabinet panel shown in the picture below you will. All you need to do is to press it to reset it and everything should be good to go.
This would work on any hot tub model. The app provides full interface control so you can set the temperature, turn pumps on and off and even set filtration cycles. Due to the diverse hot tub models and designs out there, there are different ways to reset a hot tub control panel.
These sequences are normal and display a variety of information regarding the conﬁguration of the hot tub control. M7 technology m7 is a patented balboa technology that. Flip the breaker panel switch on or press the reset button on the gfci outlet to restore power.
When the temperature of your hot tub changes outside of your range, the light will turn off. Panel button assignments 1=j17/26 2=pump 1 3=temp 4=light panel button positions 12 3 4 1 4 2 3 100 63 43 ssid # vs50x compatible j12 12 3 memory reset j43 a10, low amp mode 120 volt connections 240 volt connections black ac jumpers 12 volt connections relay control wires wiring color key typically line voltage typically line voltage for 2. Turn on the lower amp breaker first if you have a hot tub powered by 240 volts.
How to drain a balboa hot tub. Test and reset the g.f.c.i. You can also hold down two different buttons or press a sequence of buttons on the control.
533294, 5361215, 5550753, 5559720, 5,883,459, 6253227, To reset a hot tub heater you need to locate the red reset button which will probably be on the heater in the service bay of the hot tub. Remove the cover from the front of the drain spigot.
How do i unlock my hot tub controls? Type 2 refer to wiring diagram inside the cover of the control enclosure. For most models, you will need to turn off the power to the spa for a minute or two and then turn it back on again.
You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again. Pressing buttons on the topside panel, the app lets you start the tub and change settings from your smartphone or tablet. If you are unsure as to which breaker correlates to the hot tub, turn off the main breaker.
How to drain a balboa hot tub. Where is the drain on a balboa hot tub? This is an instructional guide on how to reset your sensors by unplugging them from the circuit board.
The other ml series keypads (200, 240, 260, 400, 551 and 554) do not have the locking option if they are used in the main panel. How to reset the sensors in a balboa bp501 control system print. All reminder messages can be disabled through the topside panel users menu.
Switch the circuit breaker connected to your balboa hot tub to the off position. The balboa default interval is 30 days, but some spa brands or models may be different. (1.52m) from the inside walls of the spa/hot tub and in line of sight from the equipment compartment.
If your hot tub control panel isn’t working then when it can be really frustrating. Balboa panel and manual reference guide a reference guide showing commonly used balboa panels, what systems they work with, and their operating manuals. Turn on your spa and observe its operation.
If you are unsure as to which breaker correlates to the hot tub, turn off the main breaker. People with infectious diseases should not use a spa or hot tub. Both user guide & ref.
There are generally two hard resets in hot tubs, the gfci, and the high limit reset. 2 years electro mechanical training. Secure a hose onto the spigot.
I have a hot tub with balboa electronics, the heater will not. Find out all about it here. Having said that, sometimes all you need to do is a simple reset on your hot tub control panel to clear the problem and to get it back into action.