Assuming it's going into a dumpster. Kriegerchick cut the majority of this while i kept the boys away.
How to remove a cast iron tub to install a surround unit.
How to remove a cast iron tub in one piece. This option allows you to save money and time by adding a liner to the existing bathtub instead of removing the whole unit and installing a new one. It sure is a great feeling to remove and replace a cast iron tub. A poorly inserted liner leaks and supports the growth of mold which adds to your tub problems.
Cast iron tubs are too heavy to lift out. If you try to lift it, your tub will become damaged beyond repairs. Even a small piece can weight 10 to 20 lbs.
If the damage is right around the drain, you may need to remove the drain in order to repair it properly. The tiny shards of bathtub are very sharp! Break it up with a sledge.
It’s best a professional installs your bathtub liner. During the last cut, i held the cut piece to ensure it did not fall down on the inside of the bathtub and chip the porcelain. You usually don’t need a tool to do this.
Disconnect, demo, remove existing tub. But technology for bathtubs has come a long way. How to remove the tub drain flange repairing rust chips and dings in a bathtub may require an extra step depending on where the damage is located.
Cast iron tubs can weigh over 300lbs easily depending on the size, shape, and wall thickness, which makes them very difficult to remove. Personally i'd take that toilet out first. Actually, if you could get it through your doorway, try a big heavy duty hand truck that moves refrigerators or the like.
You may have to remove drywall and slide them out, although you can often tip them up and out too. Rectangular, skirted cast iron bathtub. This overflow cover is usually directly above the plug that drains the water on the bottom of the tub.
Sledge hammer and cutting torch for the cast iron would be my solution. Your tub remains cannot be put in a trash can or residential dumpster. Those bad boys are heavy.
Smooth the edges using a grinder. Fiberglass and steel are less expensive but not as durable as cast iron, which keeps the heat in better. The first step to installing bathtub overflow drain is removing the waste and overflow is to remove the overflow cover.
Remove the drainpipe from your cast iron tub. Americast is part of that and it’s way lighter than cast iron. It’s usually hard to get an old tub out in one piece.
(if there are tub faucet handles, leave them in place if they are at least 8 inches above the tub.) use a flat pry bar or putty knife to pry off tiles. Maybe you dream of upgrading to a modern jetted model, or simply want to switch to a stall shower to gain square footage—whatever your reason, that old bathtub has got to go. You will need a way to haul it to the dump.
Hit the side of the tub in the new location which is about a foot to the end facing the drain. Removing the liner on an old bathtub can be tricky and challenging. Removing a tub faucet is a relatively easy process that only requires a couple of tools.
If your tub is freestanding, use a reciprocating saw and metal blade to cut off the drainpipe about 2 to 3 inches (5.1 to 7.6 cm) from the location closest to the bottom of the tub. Remove the tub spout and remove the wall surface all around the tub to a height of about 8 inches. Immediately the adhesive drys, you can’t remove the liner from the bathtub.
With a fiberglass or acrylic tub, cut out a chunk with a jigsaw and lift out the tub (photo 5). Takes 5 minutes, and gives you a lot more space. Bathtub replacement labor, basic basic labor to replace bathtub with favorable site conditions.
The space is so narrow (about 1/4) between the tub floor and the lifted drain that even insertnig a screw driver is a pib (pain in the b.t). Remove tub spout and tiles. It requires a lot of strength to pry away the pieces of the old material without damaging the tub underneath.
Make sure to wear safety glasses and pants. Cutouts for drain and overflow. Tub liner installations are not temporary.
The removal of the cover is an easier part of the process. Amazing how sturdy those old tubs were back in the day…and still are. Then, grab the faucet with your hands and pull it away from the wall.
And of course remove the door. Depending on what your plans are for the tub, you have several different methods you can use to remove one.