Removed the siding and i have the ledger resting on what i believe is the vinyl starter strip. Use the edge of your table as a guide and slowly saw off the excess siding.


Board and batten exterior siding photos Board and batten

Pics of ledger board and vinyl.

How to cut vinyl siding for ledger board. When slipping the flashing under the siding, be sure to slide the flashing to the left or right of the ledger by at least 2″. Slide the flashing underneath the siding 1 inch. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection.

Install the ledger overtop of the siding or remove the siding, attach the ledger and recase around it? Sep 7, 2009 #2 cut the siding out and attach directly to structure. Overlap flashing by 3 inches and cut it for the doorway.

My dad is coming up from california he is a construction foreman down there, but does not do any work with vinyl siding so the challenge for me is how to water proof it afterwords. Cut along the line you drew using the circular saw. Set the blade depth so you won’t cut into the house sheathing below the siding.

Then slip flashing behind the siding, covering the top edge of the ledger. Use your free hand to hold the vinyl siding down so it doesn't shift while you're cutting it. Start by making an outline on the siding where you want to position the ledger board.

Slide the flashing underneath the siding 1.slip flashing under the siding.snap a chalk line, cut out the siding and tack up the ledger board. Set the blade depth so you won't cut into the house sheathing below the siding. Lol does the vinyl starter strip need to be removed?

See also  How Long Does It Take For A Process Server To Serve Papers

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Slip flashing under siding snap a chalk line, cut out the siding and tack up the ledger board.

Locate the rim joist and mark an outline on the siding where you want to position the ledger board using a tape measure, pencil and chalk line. This means that the points of the teeth should be oriented opposite of the spinning direction. Use a nail as a temporary place holder to check.

Make sure you have enough room to install flashing above the ledger board and allow for at least a ¾” space above the decking, preventing water from wicking upwards into wood siding. Add 1 ½ inches to each side of the deck width so that hangers can be connected for the joists. Put the ledger board below the door threshold allowing room for the thickness of the deck materials to be installed.

How do you cut vinyl siding on a ledger board? For the most secure attachment, ensure the ledger board fastens to the rim joist, just below the floor of the house. I know the standard ledger attachment is to cut out the siding where the ledger goes, install the ledger and proper flashing on top, and caulk the ends of the ledger.

Push the saw along the line at a steady rate to get a clean, smooth cut. Once again, this contributes to giving the vinyl siding a clean cut. Lay the vinyl siding on a flat table or workbench.

See also  How To Get Freckles On Snapchat

Step 1 mark the location of the ledger against the siding.the vinyl siding interlocks with itself to form a cohesive. Then slip flashing behind the siding, covering the top edge of the ledger. Cut away the marked area of siding with tin snips.

I have vinyl siding on the house now and i know i need to cut it away to install the ledger for everything run off of. After cutting the siding with a circular saw, install the flashing. Watch the blade carefully as you’re cutting to make sure it’s staying on the line.

The bottom part of the ledger is resting on the vinyl siding starter strip. Snap a chalk line, cut out the siding and tack up the ledger board. The door area is built out about 2 1/2′ , angled at 45 degrees on each side.

Start by making an outline on the siding where you want to position the ledger board. When the back flashing needs to be cut around an obstacle, measure for the notch and cut with tin snips, or slice several passes with a knife. You should position the siding so that the cutting line is hanging off the edge for obvious reasons.

Slip flashing under the siding. What is the preferred method when attaching to a house with vinyl siding. Start by making an outline on the siding where you want to position the ledger board.

Use a level to mark the placement of the. First, ensure your circular saw is equal to the thickness of the deck, then cut the ledger outline. I've used it for cutting for a ledger (make sure you get some appropriate j to dress up the cut, just bond it on with caulk) and to terminate porch railing into the siding.

See also  How To Make A Cutting Board From Raw Wood

Wood or concrete siding will have to be cut away using a circular saw. You may want to place it lower if you intend to step down onto the deck from the doorway. Put on your safety goggles, then line up the place you want to cut on your siding with your blade.

(at least i think this is right.) but because of the vinyl siding i want to make sure i do it right. Make the outline large enough to include space for the deck boards on top, the ledger and.


HardiePanel siding with PVC trim boards creates an


Pin on Decks


Modern Clapboard Vinyl Siding Institute VSI (With


Learn how to properly install a waterproof deck ledger


Pin on Outdoor ideas


How to Create BoardandBatten Siding Looks With


Pin on Decks


Pin on Deck build


Decorative Vinyl Siding Options Cedar Shakes & Board ‘n


Vinyl Siding Vinyl siding, Vinyl siding installation


Learn how to properly install a waterproof deck ledger


13 Simple Vinyl Siding Installation Tips Vinyl siding


Pin on Got Wood?


The eaves and gutters overhang the deck by about 16 inches


Pin on Construction aids


20 best images about Pergola on Pinterest Summer porch


75 best replacing vinyl siding images on Pinterest Vinyl


Pin on BWoodworking Tips and Jigs


Pin on Everflashing's deck ledger flashing

Leave a Reply

Your email address will not be published.